PT100 Input
FlexTop 2202 is a 4...20 mA loop-powered transmitter for Pt100 sensors. Either 2-, 3- or 4-wire sensors can be used. For 2-wire sensors an automatic balancing of the sensor cable resistance is possible with shorted sensor cable. The cable resistance can be manually configured as well. Using a PC, the Windows-based Flex-program and a Flex Programmer configuring unit, the following parameters can be configured via the output connectors (2-way communication): TAG no., number of wires, cable resistance, error detection level, measuring range/unit, damping, offset and status indication. The Flex-program has a data logging facility enabling the user to monitor measuring results or calibrate the measuring setup. FlexTop 2202 is embedded in silicone which makes it resistant to humid environments. FlexTop 2202, fitting into the DIN B housing, has a 6 mm centre hole for quick sensor replacement. The spring loaded mounting screws ensure a safe fastening even in vibrating environments.
Flex Top 2211 is a 4...20 mA loop-powered, configurable universal transmitter with galvanic isolation between input and output. The input can be configured for RTD or T/C sensors, resistance, current or voltage signals. Either 2, 3 or 4-wire connection can be selected for the resistance input. The built-in temperature sensor or a remote Pt100 sensor can be used to compensate for "cold junction" (CJC) if thermocouples are connected. Flex Top 2211 is embedded in silicone which makes it resistant to humid environments. The configuration can be established from the dedicated Flex Programmer configuring tool connected to a PC. Flex Top 2211 has a 6 mm centre hole for fast sensor replacement and spring loaded mounting screws which ensure a safe fastening even in vibrating environments. A built-in temperature surveillance system gives alarm if ambient temperature limits are exceeded.
Flex Top 2221 is a 4...20 mA loop-powered, configurable universal transmitter with galvanic isolation between input and output. The input can be configured for RTD or T/C sensors, resistance, current or voltage signals. Either 2-, 3- or 4-wire connection can be selected for the resistance input. The built-in temperature sensor or a remote Pt100 sensor can be used to compensate for "cold junction" (CJC) if thermocouples are connected. The HART® communication feature on-line process calibration and adjustment, transmitter configuration and multiple process control in 2-wire networks. The configuration can be established from a standard HART® configurator or the dedicated Flex Programmer configuring tool connected to a PC. Flex Top 2221 is embedded in silicone which makes it resistant to humid environments. Flex Top 2221 has a 6 mm centre hole for fast sensor replacement and spring loaded mounting screws which ensure a safe fastening even in vibrating environments.
The SEM104P is a temperature transmitter designed to accept a standard platinum resistance sensor (Pt1002 or 3 wire) to BS EN60751, BS1904 or DIN43760 and convert the temperature to industrial (4 to 20) mA. It is housed in a purpose designed DIN standard connecting block enclosure. The transmitters are available in 6 standard factory calibrated ranges, but the transmitter can be user re-ranged to operate over most temperature ranges encountered in both industrial and building management applications. Non standard ranges can be supplied to special order. The enclosure provides trim potentiometer access, allowing fine re-calibration adjustments to be made at both ends of the scale.
The RTD in-head mounted temperature transmitter connects to any standard pt100 resistance sensor and converts the linearised temperature to a (4 to 20) mA signal. The transmitter is a two wire device, and is fully configurable by the user, over a wide temperature range, with the aid of a simple push button. This design incorporates additional configuration menus, allowing the user to push button trim the transmitter output at both zero and span, ideal for trimming out sensor errors. The transmitters advanced circuitry guaranties high stability over the wide operating ambient temperature ranges experienced by head mounted devices. One of the transmitters features is the program LED, which provides visual indication of sensor fault when in normal operation and is also used to guide the operator through the simple menus during configuration.
The SEM206 is our entry level PC programmable temperature transmitter. There are three versions for Pt100, Thermocouple and Thermistor sensors. It will convert the sensor output to a standard industrial (4 to 20) mA transmission signal. PC configuration allows the user to select range, units and burnout direction, without requiring calibration equipment. Configuration is performed quickly using our USB port driven configurator by simply connecting two clips to the SEM206 loop terminals and following the software instructions. Calibration set up may be saved as a file on the PC for later use.
The TT200 Series are our mid range transmitters for RTD, Slidewire, Thermocouple and Resistance sensors. They will convert the sensor input to provide a loop powered 4/20mA output signal. ATEX version are also available The TT200 Series have a calibration feature where the output can be matched to the sensor on the input. It can be matched at zero, or both zero and span ends of the range being measured. It is also possible to measure linear resistance up to 10K Ohms and slidewire sensors up to 100K Ohms. The software allows a user linearisation function to be downloaded into the product. This allows the user to adapt the output to suit a non linear tank for example.
The SEM210 is a universal programmable temperature transmitter which accepts most commonly used Pt100, thermocouple, mV and slide-wire sensors and generates an industry standard (4 to 20) mA transmission signal. This type of product is useful if you use a number of different sensors; you only need to hold one product in stock. The output range and other operating parameters are easily programmed using our free software and USB powered configurator. Isolation is a standard feature to overcome any potential ground loop effects and a sensor referencing facility enables the transmitter to be calibrated to a particular sensor.
Complete with HART Protocol, the SEM310 universal temperature transmitter accepts Pt100, thermocouple, mV and slidewire sensors and can be integrated into systems where the HART protocol is required. The HART communication protocol allows the user to quickly and easily download information or interrogate the device. It is small in size yet has a performance superior to other larger and more expensive transmitters. A sensor referencing facility enables the transmitter to be accurately matched to a particular sensor.
SEM710 - PC Programmable, with loop powered display, suitable for Pt100 and TC sensors
Universal Input
Flex Top 2211 is a 4...20 mA loop-powered, configurable universal transmitter with galvanic isolation between input and output. The input can be configured for RTD or T/C sensors, resistance, current or voltage signals. Either 2, 3 or 4-wire connection can be selected for the resistance input. The built-in temperature sensor or a remote Pt100 sensor can be used to compensate for "cold junction" (CJC) if thermocouples are connected. Flex Top 2211 is embedded in silicone which makes it resistant to humid environments. The configuration can be established from the dedicated Flex Programmer configuring tool connected to a PC. Flex Top 2211 has a 6 mm centre hole for fast sensor replacement and spring loaded mounting screws which ensure a safe fastening even in vibrating environments. A built-in temperature surveillance system gives alarm if ambient temperature limits are exceeded.
The TT200 Series are our mid range transmitters for RTD, Slidewire, Thermocouple and Resistance sensors. They will convert the sensor input to provide a loop powered 4/20mA output signal. ATEX version are also available The TT200 Series have a calibration feature where the output can be matched to the sensor on the input. It can be matched at zero, or both zero and span ends of the range being measured. It is also possible to measure linear resistance up to 10K Ohms and slidewire sensors up to 100K Ohms. The software allows a user linearisation function to be downloaded into the product. This allows the user to adapt the output to suit a non linear tank for example.
The SEM210 is a universal programmable temperature transmitter which accepts most commonly used Pt100, thermocouple, mV and slide-wire sensors and generates an industry standard (4 to 20) mA transmission signal. This type of product is useful if you use a number of different sensors; you only need to hold one product in stock. The output range and other operating parameters are easily programmed using our free software and USB powered configurator. Isolation is a standard feature to overcome any potential ground loop effects and a sensor referencing facility enables the transmitter to be calibrated to a particular sensor.
SEM710 - PC Programmable, with loop powered display, suitable for Pt100 and TC sensors
Hazardous Area
The TT220X series consist of 2 products, one for resistance sensors and one for thermocouple sensors. They are both approved to ATEX and IECEx standards allowing for use in hazardous area applications. The TT200X series are designed for use with RTD / Slidewire, or thermocouple sensors. Other sensor characteristics or your own 22 point linearisation characteristic (for slidewire, linear resistance or mV) can be downloaded into the product enabling you to adapt it exactly to your application.
The SEM210 is a universal programmable temperature transmitter which accepts most commonly used Pt100, thermocouple, mV and slide-wire sensors and generates an industry standard (4 to 20) mA transmission signal. This type of product is useful if you use a number of different sensors; you only need to hold one product in stock. The output range and other operating parameters are easily programmed using our free software and USB powered configurator. Isolation is a standard feature to overcome any potential ground loop effects and a sensor referencing facility enables the transmitter to be calibrated to a particular sensor.
The SEM1801/2XR ‘smart’ transmitter is designed for use with RTD or Slidewire sensors and converts the sensor signal into an industry standard (4 to 20) mA loop powered output. Pt100, 500, 1000, Ni, Cu sensors and Slide wire sensors up to 100 K Ohms can be accommodated. Other sensor characteristics or your own 22 point linearisation characteristic (for slidewire or linear resistance) can be downloaded into the product enabling it to be adapted exactly to your application. The product also has a calibrate function where the output can be aligned to the input signal. The SEM1801/2XR is approved to ATEX and IECEx standards allowing for use in hazardous area applications.
The SEM1801/2XTC Din rail temperature transmitter accepts thermocouple temperature sensors and converts the sensor output over a configured range to a standard industrial (4 to 20) mA transmission signal. Two versions are available; single or dual channel ATEX / IECEx approved for hazardous areas. PC configuration allows the user to select TC type, Range, Filter, units, linearisation and Burnout direction, without requiring calibration equipment. The product also has a calibrate function where the output can be aligned to the input signal.
SEM710 - PC Programmable, with loop powered display, suitable for Pt100 and TC sensors
HART Protocol
FlexTop 2221 is a 4...20 mA loop-powered, configurable universal transmitter with galvanic isolation between input and output. The input can be configured for RTD or T/C sensors, resistance, current or voltage signals. Either 2-, 3- or 4-wire connection can be selected for the resistance input. The built-in temperature sensor or a remote Pt100 sensor can be used to compensate for "cold junction" (CJC) if thermocouples are connected. The HART® communication feature on-line process calibration and adjustment, transmitter configuration and multiple process control in 2-wire networks. The configuration can be established from a standard HART® configurator or the dedicated Flex Programmer configuring tool connected to a PC. Flex Top 2221 is embedded in silicone which makes it resistant to humid environments. Flex Top 2221 has a 6 mm centre hole for fast sensor replacement and spring loaded mounting screws which ensure a safe fastening even in vibrating environments.
Complete with HART Protocol, the SEM310 universal temperature transmitter accepts Pt100, thermocouple, mV and slidewire sensors and can be integrated into systems where the HART protocol is required. The HART communication protocol allows the user to quickly and easily download information or interrogate the device. It is small in size yet has a performance superior to other larger and more expensive transmitters. A sensor referencing facility enables the transmitter to be accurately matched to a particular sensor.
The SEM315 is a DIN Rail temperature transmitter with HART Protocol. It accepts RTD, Thermocouple, mV and slidewire sensors. The SEM315 has full HART communications protocol which allows the user to quickly and easily down-load information or interrogate the device enabling the following:- Simple re-ranging of sensor type and range Easy on site re-calibration Self documentation Operation with proprietary software packages such as AMS Plant Web™ and Cornerstone™ Remote configuration on the (4 to 20) mA loop with a hand held communicator or with a PC & HART modem Online Digital communication concurrent with a (4 to 20) mA Analogue signal. All the standard HART universal and common usage commands are fully implemented, with other device specific commands that enable access to the enhanced performance parameters of the SEM315.
Din Rail Mount
TxIsoRail is fully programmable isolated temperature transmitters dedicted to Pt100 and thermocouple industrial sensors. TxIsoRail is a DIN rail mount unit. Both units can be easily user configured for input type and working range by means of an interface cable connected to a PC USB port. Why use isolated transmitters? Isolated transmitters protect the electrical instruments by eliminating ground loop effects and reduce substantially the undesirable interferences and instabilities in sensor measurements.
The SEM213 is a cost effective DIN rail mount temperature transmitter that accepts RTD temperature probes (SEM213P) & Thermocouples (SEM213TC) and converts the probe output to the industry standard (4 to 20) mA transmission signal. A simple push button operation allows the user to select RTD or Thermocouple type, Burnout direction, Select fixed ranges and trim 4 and 20 mA points. The SEM213 transmitter incorporates the latest digital technology to ensure accurate drift free performance.
The SEM1603 is a programmable DIN rail mounted temperature transmitter which accepts RTD temperature probes (SEM1603P) & Thermocouples (SEM1603TC) and converts their output into the industry standard 4 to 20mA transmission signal. Designed for ease of use, this range is configured with our USB port powered configuration module. The module interfaces a PC USB port to the SEM1603, using the (4 to 20) mA loop to communicate. Using our free configuration software, you will be able to read the current configuration data, and then perform any changes you wish to make to the configuration. To further help save time, the SEM1603 and configuration module do not need to be wired to a power supply during the configuration process, both are powered by the USB interface on your PC.
The SEM1610 is a programmable DIN rail mounted temperature transmitter which accepts RTD, Thermocouple, mV and passive current signals converts them into the industry standard 4 to 20mA transmission signal. Designed for ease of use, our direct USB interface is fitted for quick and easy configuration. Just connect a standard USB cable between the SEM1610 and your PC and you’re ready to go. Using our free configuration software, your PC will automatically read the current configuration data and guide you through any changes you wish to make. To further help save time, the SEM1610 does not need to be wired to a power supply during the configuration process, it is powered via the USB interface from your PC.
The SEM315 is a DIN Rail temperature transmitter with HART Protocol. It accepts RTD, Thermocouple, mV and slidewire sensors. The SEM315 has full HART communications protocol which allows the user to quickly and easily down-load information or interrogate the device enabling the following:- Simple re-ranging of sensor type and range Easy on site re-calibration Self documentation Operation with proprietary software packages such as AMS Plant Web™ and Cornerstone™ Remote configuration on the (4 to 20) mA loop with a hand held communicator or with a PC & HART modem Online Digital communication concurrent with a (4 to 20) mA Analogue signal. All the standard HART universal and common usage commands are fully implemented, with other device specific commands that enable access to the enhanced performance parameters of the SEM315.
The SEM1801/2XR ‘smart’ transmitter is designed for use with RTD or Slidewire sensors and converts the sensor signal into an industry standard (4 to 20) mA loop powered output. Pt100, 500, 1000, Ni, Cu sensors and Slide wire sensors up to 100 K Ohms can be accommodated. Other sensor characteristics or your own 22 point linearisation characteristic (for slidewire or linear resistance) can be downloaded into the product enabling it to be adapted exactly to your application. The product also has a calibrate function where the output can be aligned to the input signal. The SEM1801/2XR is approved to ATEX and IECEx standards allowing for use in hazardous area applications.
The SEM1801/2XTC Din rail temperature transmitter accepts thermocouple temperature sensors and converts the sensor output over a configured range to a standard industrial (4 to 20) mA transmission signal. Two versions are available; single or dual channel ATEX / IECEx approved for hazardous areas. PC configuration allows the user to select TC type, Range, Filter, units, linearisation and Burnout direction, without requiring calibration equipment. The product also has a calibrate function where the output can be aligned to the input signal.